Ventilation in the dressing room: options and methods for arranging the air exchange system

Alexey Dedyulin
Checked by a specialist: Alexey Dedyulin
Author: Yuri Vladimirov
Last update: December 2024

Have you planned the construction of a comfortable bath? Already built it, but did not decide on the ventilation? We will tell you about what should be the air exchange in the dressing room. Agree, it’s better to spend a little more time on theory than to redo something later. Proper ventilation in the dressing room is needed for the entire bathhouse as a whole.

It is impossible to make a good bath without well thought out communications. Thanks to our material, you will find a balance between heat and cold in the dressing room, you will not have problems with condensate. The finish will be dry and the air as humid as needed. As a result, the bath will last for many years without repairs, and you will not risk anything.

The nuances of air exchange in the dressing room

The bath consists of alternately connected rooms with its purpose, temperature and humidity. Each of them needs care. Some owners leave the dressing room without ventilation at all, and this is wrong. The room is waterlogged and deteriorated. For dressing rooms there are three main options for air exchange, which we will talk about a little below.

The dressing room is a strip room in front of the washing room, and it is often combined with a rest room. Usually there stoke the stove. The dressing room is aired simultaneously with heating and after bathing procedures. A well-chosen ventilation scheme will give the room more fresh air and facilitate constant care.

The ventilation system in the dressing room performs three main functions: removes dirty air, delivers clean air and heats it to a comfortable temperature.

Dressing room on the plan
A typical dressing room in an individual building with an ash pan of the stove, an entrance to a separate sink and then to a steam room, with a 2: 1: 1 ratio between these rooms

In the dressing room it is also arranged in order to regulate the humidity and temperature throughout the bath, to normalize the temperature in the rest room. This should be taken care of while the furnace and rest in the steam room. An oven also needs fresh air.

Further air exchange is directed to the drying of the room. Wood quickly deteriorates from moisture, especially in the dark. Due to moisture, windows and doors can sometimes not be closed tightly. Microorganisms in a damp room emit unpleasant odors, and the wooden finish absorbs them and “seals” them.

It will be difficult for vacationers to adapt to air quality. But, proper ventilation after bath procedures will eliminate the bad smell and extend the life of the building.

Circulation in a combined dressing room and steam room
One of the options for circulation in the dressing room in the rest room, with air supply through the opening at the top above the stove and a pipe under the stove coming from the street - it will be hot for the rest room, but some attendants will like it

Ventilation is calculated on the basis of such conditions:

  • high humidity and a lot of steam;
  • condensation forms;
  • air exchange and temperature in the bathhouse have to be adjusted only on some days;
  • hot air;
  • carbon dioxide accumulates;
  • there may be harmful combustion products;
  • small window size.

In an ideal bathhouse, nothing threatens the health of visitors, and the conditions meet the requirements for a bathhouse rest. In the pre-bathing room, it is worth organizing two types of ventilation, natural with gravity air and one more choice: mechanical or combined. In the latter, inflow is usually made gravity.

Which ventilation scheme should I prefer?

Achieve the right ventilation in the bath It’s not easy. If you are just designing a bathhouse, take care of the small windows, micro-openings between the rooms, the supply openings with access to the street and plugs. But do not place exhaust openings on the ceiling to avoid overcooling the dressing room.

In the bathhouse, lay the correct proportions. The optimal combination of the size of the dressing room (combined with the rest room), washing and steam room:

  • 2 : 1,5 : 1;
  • 1,5 : 1 : 1;
  • 2 : 1 : 1.

Make a separate dressing room the same size as a sink and steam room. On the combined, take half the length and the entire width of the building.

Small dressing room as a dressing room
A separate dressing room is a dressing room with a need for fresh air and an exhaust hood for venting steam, which can be placed in an external room or here, if the size of the building is small

Follow the rules and recommendations:

  1. Achieve equality between supply and exhaust flows.
  2. Only buy mechanical fans that are moisture resistant.
  3. The required ventilation rate is more than 3 m³ / hour per 1 m².
  4. Combined ventilation with forced draft and natural influx should be added to the holes between the rooms and the wooden windows.
  5. Part of the hot air would not hurt to redirect from the steam room to the dressing room.
  6. Route the air exchange path between the supply and exhaust by the toilet.

Think about the universal option. ventilation steam rooms. To do this, place the door to the steam room near the ash pan. On the wall opposite the oven, make an exhaust opening 15–20 cm wide on the wall. Leave about 20 cm between this vent and the ceiling, focus on a height of 2 meters above the floor. Be sure to install an axial fan if the exhaust opening does not go directly into the street.

There is another option with a ventilation pipe. Make it vertical, but then turn it and at an angle connect it to the direct channel above the steam room, if there is one. Make the diameter of the pipe large above the place of union. In another case, take her out of the dressing room exactly through the roof.

Axial exhaust fan
So that the performance of the exhaust axial fan does not decrease, wrap it with foam foam or at least its narrow part

Place the air inlet half a meter above the floor. Choose a place approximately diagonally relative to the exhaust. Make the supply aperture the same size as the output (15-20 cm). Swipe to the street and also add a blank. Thanks to it, you can influence the speed with which incoming air will push out the internal. The inflow is amplified by an additional hole next to the ash pan for supplying air directly to it.

Insulate exhaust pipe and the dressing room itself, so that there is a minimum of condensate. Thermal insulation will also make the air warmer, and after visiting the steam room it is better if the air temperature is comfortable. Make a circulation with a smooth change in temperature along the height of the dressing room and on the way from the locker room, through the sink and to the doors of the steam room.

Be sure to insulate the floor. For a combined dressing room in the relaxation room, make ventilation based on the largest possible area per person and not less than 1.3 m² per one.

Consider the tightness of the bath. The frame building requires an enhanced air supply: it is better to install a supply fan in this.

Do windows no more than 45 cm wide, preferably only from wood. Set the front door to a size of approximately 180 × 80 cm. It is better to make the interior doors a little smaller in order to reduce heat loss.

Scheme # 1 - with open circulation

Consider a combined dressing room and a classic version of the situation.

Consequences of moisture accumulation
At first, moisture will not cause inconvenience, but then the condition of the ceiling made of wood will deteriorate - it will not work properly to relax in the emergency building

The first wall is narrow, with an entrance door. The second - with a doorway in a separate washing or combined with a steam room. A meter from the interior door, within the dressing room, have a stove. The third wall is narrow, opposite the wall with the front door. The fourth - opposite the second, with seats for rest.

Make natural air exchange in the form of windows and also collect combined ventilation.

Do the third wall air inlet and always with a stub. Place the opening at a height of 50 cm from the floor, approximately in the middle of the wall, but with a slight offset towards the stove.

At the end of the fourth wall far from the tributary, arrange an exhaust opening. Cut a hole in the upper corner at a height of about 20 cm below the ceiling. Insert the exhaust fan into the opening.

It remains to make the dressing room warmer. Together with this task, they solve the problem with the removal of air from the steam room. There he is collected under the floor, and through the pipe he will fall into the dressing room. Make not only air supply, but also disposal.

There are three solutions:

  1. Direct the pipe from the steam room to the dressing room and place the exit directly next to the ash pan.
  2. Bring the channel to the wall, and after that the air will enter through the hole.
  3. Lay the pipe below and make a cut in the floor next to the ash pan.

The air coming from the steam room will be warm enough, and the stove will heat up more intensively due to the fact that it takes it.

Scheme # 2 - with closed air circulation

In this case, you can organize a dressing room without air from the steam room.

Ajar window in the waiting room
For natural ventilation, install a wooden window with a hinged mechanism and fix it with a small gap: even at minimum mode, condensation will not form, and the temperature can be raised by steam from other rooms

At a height of 40-50 cm from the floor, cut the supply aperture with a plug - on a narrow wall adjacent to the one where the stove is. Make a hole not in the middle of the wall, but closer to the ash pan.

From the angle between the tributary and the stove, draw an imaginary diagonal and at the end of a long wall, at a level no higher than half a meter from the floor, organize an exhaust duct. At about the same height as the tributary, but possible lower.

Do not make a hole in the wall; instead, install a vertical pipe. Above the ceiling, enter the canal into the exhaust pipe rising from the steam room, and if it is absent, take it out through the roof. Install a deflector on the pipe head.

The air in the upper part of the room will already be warm, but first it will go down and go into the exhaust outlet not as fast as in the first scheme. Such a hood will also protect against excess steam, so in a waiting room, where its minimum, a closed circuit will be all the more effective.

Scheme # 3 - supply and exhaust on one wall

It is useful with different options for the location of the stove.Including if it is in the very corner.

In this scheme, you do not need to strive for a diagonal arrangement, but do not place the hood even above the inflow. Due to local ventilation, the dressing room will sooner or later become waterlogged.

Ventilation schemes for the dressing room
Three main schemes with conditional display of air exchange, when the main part of the furnace is located behind the wall. Remember that you need to achieve the maximum diagonal arrangement of the inflow and exhaust

The inflow is located directly opposite the ash pan or obliquely. At the same time, you need to focus on the fact that the cold incoming air does not blow on vacationers. A stash will get inside from the street and head straight to the ash pan of the stove, which will heat the room. Part of the air will go into circulation.

With an oblique arrangement relative to the ash pan, this volume will be larger. Place the inflow half a meter above the floor or slightly lower if the furniture will interfere.

On the same wall at the top, make an exhaust hole. Cut it obliquely relative to the tributary: as far as possible from it, and not lower than 25 cm from the ceiling.

Warm-up and warming of the dressing room

Between the locker room / relaxation room on the one hand and the steam room on the other, ideally leave a smooth transition between temperature conditions.

There are four options to achieve this:

  1. The stove goes into both rooms.
  2. An additional partition between the steam room and the dressing room, combined with a relaxation room.
  3. Part of the heated air is supplied from the steam room.
  4. On the direct route from the dressing room to the steam room is the washing.

It is also necessary to take care of the insulation of the room. From the cold isolate the floor, walls and ceiling. Often take foil insulation, but on a thick layer of foil should be laid manually.

Mineral wool for insulation
Mineral wool, polystyrene foam and other foamed materials, as well as expanded clay, are suitable for warming the dressing room, but mineral wool will be best in structure, especially if it is foil

Floor insulation start with the fact that to the lower parts of the log, located with a step of 45-55 cm, cranial bars of a smaller size are nailed - longitudinally to the base. A rough coating is laid on top - oblong or wide boards. The rough floor is formed solid.

The resulting structure is coated with a waterproofing membrane. Lay so as to completely press the layer to the protruding lags. Then, in the interval between these planks, a proportionate piece of insulation cloth is laid: a little larger in width, length and height. Mineral wool is also suitable as thermal insulation. It is taken more, since the material is strongly compressed.

The vapor barrier is laid higher with a slight approach to the walls. In the process, pipes are insulated, which will be in the thickness of the floor or lower.

It remains only to make the floor itself. The surface can be paved with tiles or boards. Usually they choose wood, so it turns out a warm floor and the unity of the interiors is maintained. The coating must be made continuous, pushing the boards to each other as much as possible.

Under the ceiling, the finish spoils the most, so use a thick layer of insulation. Thermal insulation can be collected on the ceiling, between the slats. Put a vapor barrier at the bottom, a heater above, then waterproof it. You can cover with cement screed and wooden boards from above.

You can read more about ceiling insulation in this stuff.

Insulation of the ceiling over the dressing room
The option of thermal insulation of the ceiling above the dressing room: tightly laid expanded clay, hidden in two layers of vapor barrier, and a wooden plank floor without screed

It will be possible to insulate the log houses in the finished building, but it is worth planning the thermal insulation in advance. It is also worth taking care of the insulation of the front door.

Due to thermal barriers, they effectively fight against excess moisture, but condensation can be completely avoided if some things are constantly done. Keep the doors closed, open only for a short time. Adjust the gates in the ventilation grilles.

Use plugs and first of all during warming up.After the procedures, cool the dressing room through open doors and windows. Do short drafts at the same time. Ventilate each room in turn - through their windows.

Conclusions and useful video on the topic

Combined dressing room, and how to heat it:

Analysis of the arrangement and ventilation of the dressing room, how to remove dampness and mold - in great detail:

Elements for bath ventilation - pipes, valves and grilles:

Sometimes the dressing room is a small dressing room, but usually it is combined with a rest room. In the second case, you will need full powerful ventilation. You can apply one of the three schemes described by us.

Build on the air exchange requirements that we wrote about. Remember that it is worth adding insulated surfaces to the combined or mechanical ventilation system, then the life of the bath will increase.

Write comments and ask questions about the topic of the article. Perhaps you have a bathhouse and you had to deal with the arrangement of its ventilation? Tell our readers about this. The feedback form is under the article.

Was the article helpful?
Thanks for your feedback!
No (0)
Thanks for your feedback!
Yes (0)

Pools

Pumps

Warming